Monday 23 June 2014

changing hands


A quick selfie showing the old owner handing 3591 NG over to the new owner before he drove his horse box away, loaded up with a front scuttle, the bulkhead, folding doors, panels, wings and boxes of parts; the chassis to go Tuesday morning.

Beneath the horsefeed, 3 front panels. The Goat Lady's on the bottom, the Morris one NG came with, and the new ex-stock Austin one Mike Cotton sold me. And, on top of them, a mangled spare wheel carrier. The latter is a case in point: the buyer's appreciation of that mangled bit of iron's worth tells me he understands J Types.

He came highly recommended by Roly. After my various dealings with dodgy characters in the past, who take advantage of a J Typer's good nature, it is good to know that NG is going to be finished by a true enthusiast.

Will I be gutted when it is finished? I don't think so, now. I thought I might be, but the time was right to sell. However close to being finished it might be, I knew in my heart of hearts that it would not be me who did it. The buyer was enormously complimentary about all my metalwork on the scuttle, how complete the rolling chassis is and about how easy I have made it for him to finish it off.  So, I wish him well with it.

Thursday 19 June 2014

SOLD!

Thank you all for your interest and kind offers; have never before been offered desirable sports cars as swaps! Discretion dictates that I give no details of the sale. But what I will say is that both the seller and buyer are delighted, and I am especially pleased to be able to report that the 101 is staying "in the family", so to speak; it is not going to some opportunistic dealer, but to a real enthusiast. And so gratifying that he had read this blog from start to finish and so appreciated what I have put into the project. 

Saying goodbye to 3591 NG will be a wrench after all these years, but it will be good knowing that someone is going to finish her properly.

Wednesday 11 June 2014

A summary of work done

The project has involved the repair of much of the scuttle and replacement of lots of panels. Please click on the following links:

"A" pillar ; inner arches ; inner wing ; panel interior ; dash panel with captive nuts ; outriggers ; radiator frameradiator sides,dash repairrad blanking platecab floor support ; quarterlight sill


Clutch replaced






Running chassis 98% complete

with newly forged leafsprings front and back and brakes re-lined, hydraulics replaced

                                


radiator re-cored and mounted in a rad stand I fabricated myself

 Parts and panels bought and third party work carried out





.

Tuesday 10 June 2014

Breakdown of expenditure for those considering buying my project

The following is my verifiable outlay so far (in terms of parts and third party labour)

Initial purchase price    551.00
McKenzie inner arches approx    30.00
McKenzie front valance   58.00
McKenzie front valance top panel   14.00
engine work by third party   90.00
re-core radiator   217.38
newly forged leafsprings all round   634.50
bush shackle   9.40
wheels shot blasted and re-painted (900 two-pack)by third party   100.00
fitting tyres to wheels   50.00
petrol tank repaired 60.00
POR15  25.00
starter motor 59.00
hydraulic pipe kit (made to measure) 104.12
rear shocks   44.99
engine mountings   11.48
12.59
side lamps   82.00
front shocks   47.52
classic tyres   497.10
king pin set    44.00
pull off springs   42.65
brake shoe re-lining   88.00
wheel bearings   24.45
front wheel cylinders (MG TD/TF)   99.35
two mater cylinders   105.00
misc bushes from NTG 9.40

Grand Total    £3,110.93 

PLUS
other expenditure for which I can't find the receipts:
clutch plate, clutch cover and thrust bearing, 
ex-stock, brand new and primed Austin 101 front panel
handbrake cable
track rod ends
etc

Any price finally agreed upon would have to cover at least the outlay so far on parts. I do not know how to quantify the work done to get the van to the stage it is at now. Have a look at how far I have come, by looking back through the blog. What we have now is a rolling chassis with engine (run on test bed but needs finished carb and exhaust), gearbox, prop shaft, breaks (hydraulics to be completed), wheels, tyres, shocks and leafsprings. To go on to it we have a front scuttle on which I have done lots of work, but which is not yet finished. Also have lots of metalwork done on inner arches, steps etc.

I also have lots of other parts: doors, wings, inner wings, sliding door runners, cab back, floor supports, floor panels, headlamps (originals and replacements), etc







Saturday 7 June 2014

Selling the project

Well folks, I think I have finally given up. I have bought another plane, started another metal project, set up self-employed and ...well, the list goes on. But the long and short of it is that I have run out of steam for my Austin 101 and need the garage and mental space.

Readers who have followed the project in the past will know how much work I have done on it over the years. Loads of metalwork. The engine now runs and is mounted back on the chassis in  front of the gearbox and shaft on fresh rubber mounts. 

It has new brakes, new hydraulic piping, new slave and master cylinders, a thousand pound's worth of 5 brand new classic tyres. Newly forged leaf springs all round and freshly mounted new shock absorbers. The scuttle is nearly ready to be mounted on the front of the chassis around a newly re-cored radiator, sitting on a newly fabricated frame. 

I shall be working my way through the receipts to try to work out just how much I have spent on parts over the years, and other than recouping the initial outlay, I only expect to recover the cost of parts and re-fabricated parts. 

Nothing will compensate for the thousands of hours spent on the project, but that never matters. Nobody does it for the money. It is all about the pleasure of the challenge. Someone keen could finish the project in about 6 months...,and I don't think I want to know about it when they do, because it is too frustratingly close to completion and I don't need my nose rubbed in it.

But I just know that I don't have the motivation, now, to finish it...and more importantly, I have other things making demands on my time.

So, get in touch if you are interested. If I don't sell privately in the next couple of weeks or so, I think I shall put it on ebay.

Read back through the blog to see what you'd be getting for your money.